Cheap LED Flashlights – Are They Worth The Lower Price?

LED flashlights have grown considerably in popularity. The technology, like anything cheap flashlightutilizing the results of research and development, continues to improve. But flashlights have become much like any other electronic item, in terms of quality, you DO get what you pay for! No doubt, most of us are on a budget and we always want to get the most for our money no matter what the product is. So how does all this pertain to cheap LED flashlights? Read on.

Like anything we buy, amidst the quality products, there’s usually a knock-off available somewhere.

Let’s look at the major components of an LED flashlight, and decide which parts can be made cheaply.

Piece by Piece

  • The Body:
LED flashlight finish

Tough anodized finish

Many of today’s major manufacturers use a form of scratch resistant type III anodizing. The aluminum used is often aircraft (or aerospace) grade. This produces an extremely durable light! Virtually indestructible in fact. This durability will most likely NOT be present in a cheap knock-off light.

  • The Body, When Wet:

Most flashlights today are waterproof. They’ll be designated as ‘Waterproof to IPX-8 standard’. This is an international classification meaning the light can be immersed in water. In accordance to a rating system known as FL1 Standard, waterproof will usually mean the light can withstand immersion 1 meter deep for 30 minutes. Most likely the cheaper light cannot withstand much more than simply getting splashed with water. Lights are available for divers where underwater operation may be needed for up to four hours at a time. For these lights, the meter depth would be listed on the package.

  • The Emitter: (LED)
flashlight LED

Smooth reflector

flashlight LED

Look deep into my LED!!

The emitter is perhaps one of the most important parts of a flashlight.

Deep in the center of the reflector is what produces the beam of light. Emitters have come a LONG way over the past decade. CREE is the major manufacturer of emitters. Just about 100% of all LED lights will feature a CREE emitter. Basically, a cheaper LED light will feature older, first generation emitters which when compared to some of the newer emitters will be somewhat less efficient. This means two things; the light will not achieve as high a brightness, and the overall run-time of the light could be significantly less.

  • The ABC’s of an LED

If you see a flashlight with the following description; Cree XR-E Q5-WC LED emitter; or XR-E R2… you are definitely NOT getting a product utilizing the latest technology. If the light you’re looking at features an “XR-E” LED, then you’re looking at something that was cutting edge, back in 2006!! This post describes different LED’s in more detail. The advancement in emitter technology has also lent itself to better regulation and overall efficiency, as mentioned above. In plain English, this means that in most cases your batteries will run the light longer. In turn, the electronics will keep the “driver” working  harder to provide the maximum amount of light even as the voltage (due to a weakening battery) begins to drop.

Hot Stuff

Most, if not all LED flashlights will get hot after a few minutes on its highest setting. Again, depending on price, good heat dispersion will be a factor. For the cheaper light, this could shorten the life of the electronics. If the entire body of the light gets hot, the batteries might be affected as well. Too hot to handle can be taken literally in this case. The pricier light might often feature “fins” that dissipate the heat, while some even “step-down” automatically (in lumens) to a safer output if left on high for more than a few minutes. The reviews from many users of cheaper lights have complained how hot there’s became after a short time. Excessive heat from the LED occurs naturally, but should be monitored. Some lights handle it better than others. The point is, heat can shorten the life of the unit. Although unpredictable, your best resource for this are user reviews.

The Beam is Where It’s At

Another BIG consideration when pondering the purchase of a cheap flashlight, is beam pattern (or profile). The photos illustrate both a “classic” LED beam from a brand-name light and one from a cheaper lesser-known brand. You can see in pic 1 that the brand-name beam is basically smooth from the spill area, right up to the corona and the hot spot. When the head assembly in any given light uses either cheaper components, or isn’t assembled correctly, the beam might feature several artifacts which are comprised of “rings” around the beam, or an noticeably uneven beam. The beam in pic 2 also illustrates when the shape of the LED is noticeable…creating the “squarish” appearance in the center.

Typical beam pattern of an XM-L2 LED

Standard LED beam

LED beam on cheap light

Bargain-light beam

 

 

 

 

 

 

Build (and brand) Quality

The electronics in each light will probably not vary too much. The rear clicky switches will most likely function much the same. However reading reviews from a handful of users who’ve bought a light for less than $10, have reported faulty switches. What you’re paying for in a good quality light, is the overall construction, its durability, and its ability to actually work when switched on! It would be foolish to say that brand doesn’t also play a factor in price. This is true with everything. Wouldn’t you assume you’d pay more for a Sony TV, vs. one made by Sansui? Consider though that a great deal of research & development has gone into these tools. And tools, are what they are.

Lower Voltage, Less Choice

A cheaper LED flashlight may often not feature the voltage range of its more expensive cousin. The voltage range of a lithium battery-based light will often be as high as 8 volts. This allows for a greater choice of battery configurations. On the cheaper end, the voltage range might not be noted, nor will there usually be an instruction manual with the light you receive. Therefore a single 18650 battery light, (3.7 volts) may not accept two CR123’s as an alternative, since that means the light would need to accommodate over 6 volts.

No Regulations

The majority of flashlights on the market are assembled with quality components which work to provide constant light through regulation. This means that the level of brightness you see will remain CONSTANT until the battery can no longer provide ample voltage.

In most cases, the circuits found in the cheap lights will not have the ability to regulate output. This means the beam will begin to deteriorate quickly with each use. It will loose brightness at a steady rate until the battery is dead. Admittedly, this is how flashlights that ran on standard C, D or AA batteries have performed since their invention. But, with the introduction of LED’s and intelligent circuitry, we’ve become accustomed to a more uniform output.

Let’s Review  Truth Word Compass Conscience Lead to Honesty Sincerity

Consider these fundamental differences in what a cheap LED flashlight will tend to offer, when compared to a name-brand moderately priced light;

  • Older, less efficient emitter
  • Lack of heat dispersion
  • The lack of multiple modes (only high, low & strobe) no medium or moonlight mode
  • Overall cheaper construction — less durable — greater chance of mechanical failure
  • Not waterproof or water resistant
  • Possible uneven beam with artifacts
  • Lower voltage acceptance means less variety of battery choices
  • Lack of output regulation

Decisions, Decisions decisions-choices-concept-18235922

Ultimately, the final decision is yours. If you’ve recently discovered the world of LED flashlights and are interested in building a collection, one based on low-cost alternatives might be one that you’ll discover needs replacing more frequently. A quality name-brand light (more often than not) should last for many years! Yes, we realize how electronics can become obsolete from year to year. But the advancement in LED’s has grown so much over the last five years, that it’s unlikely it’ll change THAT much again, over the next few years.

The issue most pronounced with many inexpensive lights lies in the claims by their manufacturers. I cannot honestly say that I’ve never been aware of any product exaggerations in a name-brand light. This cannot be said for many of the cheaper brands. It’s usually in lumens where they tend to inflate the numbers. They like to boast higher lumens than the light is capable of producing.

Brand Power

What are the brands to look for? Fenix; Nitecore; Sofirn; Astrolux and Olight… just to name a few. The age-old adage, “let the buyer beware” is still as true today as it ever was.

Questions or comments?

I’d love to hear from you!

You can compare prices on quality flashlights here.

 

Please follow Lightsngear and like us:

18 Comments:

  1. If you want to buy a flashlight, it seems that was not a difficult position to decide, but I see that it is not. Because there is much variety in terms of technology, what just found me, now if I could choose a good flashlight with the help of this information. I’m glad I found this site and I’m sure that I’ll get into this product when making my purchase. Congratulations

  2. Came here from the YouTube link. Thanks for this article. Great site. I’ve bookmarked it.

  3. depends on what you want

    for light duty, cheap lights can be fine

    right tool and price for the job

    wle

    • That’s true to a point, but if you plan on using the light a great deal, then spending the extra on something of higher quality is going to provide better, longer-lasting performance.

  4. Very good and helpful article
    Thanks for it

  5. The line “look deep into my LED!!” keeps me smiling every time I read it! 🙂
    Thanks for all the information giving me a better understanding of the alphabet in LED flashlight terminology (and how way backward we are on our side of the globe) however cheaper prices do prevail – $35 = rm150 for an AA.. ooh – your guide is helping me make more knowledgeable decisions though . Thanks again

  6. WOW! I always thought my brother,who died 15 years ago, was a little “much” in liking Flashlights, but now I “see the light”ahem! It is exciting. One question, are there storage, or lifetime. variations in dif. RECHARGE power batteries? I know the selling points for standard AAs ect. ect.O.T.C.s but how can we know or hope this type will work 20 years from now? THANKS,jon old.

    • Hello Jon,

      If I’m understanding your question properly, you’re asking if some rechargeable batteries last longer overall, than others. This is an interesting question, but not something that I have a definitive answer for. From what I know, I believe most are equal to one another. As long as they’re made from quality components (and many brands actually use Panasonic cells) then they should be good for the advertised use of roughly 1000 charges. Cheaper batteries won’t fair nearly as well.

      Thanks for the question.

      • What I hate most about the cheapies, they have no memory, so they start from low, or – even worse – with the mode next to what is last used. Or they can’t be turned off at once; you’ll have to go through all the modes to reach off!!

        • Exactly! Most that I’ve seen default to high, which for most “newbies” seems acceptable. These folks only seem to want the brightest light at all times, and can’t fathom being in a situation where only the lowest output is required.

  7. The LiFePo4 batteries will last much longer, but they have a lower voltage of 3.2V and require a designated charger. The batteries in cars and bikes are of this technology.

  8. Another disadvantage of budget lights is the use of PWM (Pulse Width Modulation).
    This dims the light by turning it on/off at a high frequency, instead of limiting the current electronically.
    The disadvantages are, they’re less efficient and fast moving objects will show a strobe effect.

Leave a Reply

Your email address will not be published. Required fields are marked *