This is probably not your first introduction to the Ultrafire 502b flashlight. They’ve been a popular item on the internet for quite some time. It was due to the publicity of the 502b that prompted me to order one from Amazon.

 

As you can see from the big crisp image above, the light I received says “XD-502B” on it. Most of the versions of this light I’ve seen online, say “WF” on them instead of XD. I’m not sure if it makes any difference, and I’m guessing it doesn’t.

Five Points of Light!

To My knowledge the 502b doesn’t have too many imitators, therefore the specifications of the light I received are probably quite similar to what you would get as well.

The 502b’s smooth reflector

The LED within the 502b

  • It measures just over 5 inches long with just over 1 inch in diameter
  • Its body is black anodized aluminum
  • It features a standard recessed tail-cap switch with the ability to tail-stand
  • The CREE LED is an XM-L T6
  • Its top lumen mode is NOT 900, as Amazon would lead you to believe
  • The version I received features 3 constant lighting modes; High, Medium & Low — in addition to Strobe and SOS.
  • It operates on ONE rechargeable lithium 18650 battery which is NOT included*
  • Not pictured, is the included pocket clip…which appears pretty sturdy.

*Most flashlights of this type can operate on either a 18650 battery OR two smaller batteries. But I don’t believe the voltage on this light is capable of handling more than 4 volts. Therefore only ONE 18650, at 3.7 volts, is all it can handle. 

Three Easy Pieces

Without using any tools, here are the three main pieces the 502b disassembles into.

Head (bezel) body-tube and tail cap. Since the bezel and tail are spring-loaded, the light should accommodate just about any 18650 cell…including flat-tops. The threads are VERY shallow and don’t come with any sort of pre-lubrication. The “thin threads” can become weak over time and might not allow for a secure seal. This is an issue if you’re looking for a 100% waterproof flashlight. Speaking of water… I’d keep it away from this light at all costs! It’s probably okay in the rain or getting splashed, but don’t even THINK of submersing it! The o-rings are less than stellar quality and water could seep through the head as well.

In the light I received, the head assembly is loose. If I pull on the spring (which you can see in the photo) the whole piece jiggles up and down, and it also rattles if I shake the piece on its own.

Let’s Turn It On!

With battery inserted, just press the tail cap. You’ll instantly be in HIGH mode. To switch to the other modes, just give the cap switch a soft press. Each subsequent press will sequence through all the modes.

High mode on Ultrafire 502b

The photo here illustrates the beam pattern of the 502b on HIGH. It’s a relatively clean beam with no visible artifacts. The center is a bright spot of light, with a reasonable amount of spill to light the area around it. (the camera image doesn’t capture the spill you’d see in reality).

Without a light meter, determining how many lumens the Ultrafire 502b puts out is difficult.

Some internet descriptions claim the light exceeds 900 lumens. I’m 99% certain, that is incorrect. Regardless of the claim, it’s still pretty bright…just not AS bright as often claimed. There’s also not much of a difference between the three modes. The spacing between high, medium and low is very subtle. You’ll see a difference between high and low, but not much between high and medium. Low mode on the 502b would be a good medium on many other comparable lights.

Click the indoor images for a full-size view on each.

Ultrafire 502b – low

Ultrafire 502b – medium

Ultrafire 502b – high

 

 

 

 

 

As you can see from the indoor images above, there’s very little variation in brightness between the modes. The only real difference is from low to high…and even that isn’t as dramatic as it is on most other flashlights.

The first two outdoor shots, depict the comparison between high and low mode at a distance of about 75 feet.

The other two are the same, taken at 20 feet. (they can be clicked on for a larger image)

Low at 75 feet

High at 75 feet

Low at 20 feet

High at 20 feet

 

 

 

 

 

Overall; A “C Plus”

So, here’s what I DON’T like about the 502b.

  • It has no “mode” memory
  • Cycling through ALL modes (including strobe and SOS) to get to the specific mode you want can be tedious
  • The low mode is in the neighborhood of 60 lumens
  • Its intolerance to accept more than 4.2 volts means your battery options are severely limited
  • No heat dispersion.  So after running the light on high for about 3 minutes, the head  gets hot. This can be bad news for the LED driver if left on too long. Consider switching to a lower mode when this occurs.

So considering the lower price of the Ultrafire 502b, I guess a C+ is a decent grade. For longevity and reliability, I’d sooner have a “brand name” light on my belt. And Ultrafire products can be temperamental sometimes. In this article, I discuss the pitfalls of buying a lower-priced light such as this one. However everything has its exceptions in some way or another.

If by now you feel that the 502b is for you, just click!

Questions or comments on this article can be left below…for which I’ll address as soon as possible.

 

 

 

 

BR Wilkie

View Comments

  • Hi Ben,

    Thank you for this review - I actually had not heard of the Ultrafire 502b.

    I love how you show the real pictures of the low and high lighting at different ranges.

    Keep up the great work!

    Blessings Be,

    - Rich

  • Hi, I wanted to point out something that you missed in your review. Based on the picture you included of the LED emitter, I was able to determine that it is not a genuine Cree product. That is a counterfeit Cree produced by LatticeBright in China. The square bonding wire pads on the emitter along with the very blue tint of the light are hallmarks of this company. You along with many thousands of others were duped unfortunately.

    • Hi Jamie,

      Yes, I am well aware of how LatticeBright LED's get placed in cheap flashlights. Since this review I have informed (and warned) hundreds of buyers that their chances of getting ripped off are much higher when buying these types of products.

  • I have had a 502b for quite some time. It does indeed have a Cree LED.... an XP-L2. These LEDs can produce greater than 1000 lumens.
    To cure the large spring issue, it was removed. A 4 MM spacer ring was installed between the reflector and the glass. I prefer the spacer to the spring. So far it is a solid EDC light.

Recent Posts

Jetbeam E26 Kunai UV Flashlight Review

I haven't owned a new Jetbeam flashlight is quite some time. Having said that, I'm…

2 months ago

Nitecore HC65 Headlamp Review

Since the motto of Nitecore is "keep innovating" please join me now in this review…

7 months ago

Nitecore EDC33 Lumin Shield Flashlight Review

As Nitecore continues to implement new concepts with LED flashlights, let's dive in with my…

10 months ago

Wuben X3 Wireless Charging LED Flashlight Review

This is different! The Wuben X3 "Owl" is a dual-LED flashlight that features wireless charging…

12 months ago

Imalent MS03 High Lumen Flashlight Review

I've had a few flashlights from Imalent over the years, and today I'm reviewing one…

1 year ago

Acebeam E75 USB Rechargeable Flashlight Review

Today I'm reviewing the Acebeam E75. Stick around for this one....because I think you'll like…

1 year ago

This website uses cookies.